Paste number 60575: ds207+ log

Paste number 60575: ds207+ log
Pasted by: sylver
5 days, 19 hours ago
None
Paste contents:
Raw Source | XML | Display As

         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** LOADER **
 ** MARVELL BOARD: Synology Disk Station LE

U-Boot 1.1.1 (Aug 10 2007 - 19:12:18) Marvell version: 1.11.2

DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB
[4096kB@ffc00000] Flash:  4 MB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
Using default environment


Soc: 88F5281 D0
CPU: ARM926 (Rev 0) running @ 500Mhz
Orion 2 streaming disabled
VFP initialized to Run Fast Mode.
SysClock = 166Mhz , TClock = 166Mhz


Model: DS-207+
CPLD version: 0x0
FAN Status: Running

USB 0: host mode
CPU: Write allocate enabled
Net:   egiga0 [PRIME]
Press Ctrl+C to abort autoboot in 1 second



Synology> set ipaddr 192.168.0.199
Synology> printenv



bootcmd=bootm FFC00000 FFE00000
baudrate=115200
loads_echo=0
serverip=192.168.1.52
stdin=serial
stdout=serial
stderr=serial
cpuName=926
CASset=min
enaMonExt=no
enaFlashBuf=yes
enaCpuStream=no
enaVFP=yes
enaWrAllo=yes
enaICPref=yes
enaDCPref=yes
MALLOC_len=4
ethprime=egiga0
bootargs_root=root=/dev/nfs rw
bootargs_end=:::DB88FXX81:egiga0:none
image_name=uImage
standalone=fsload 0x400000 $(image_name);setenv bootargs $(bootargs) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end); bootm 0x400000;
bootdelay=3
disaMvPnp=no
ethaddr=00:00:00:00:51:81
overEthAddr=no
usb0Mode=host
bootargs=console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw syno_hw_version=DS207+v10 ihd_num=2
ethact=egiga0
ipaddr=192.168.0.199

Environment size: 736/8188 bytes



Synology> set serverip 192.168.0.20
Synology> tftpboot



*** Warning: no boot file name; using 'C700A8C0.img'
Using egiga0 device
TFTP from server 192.168.0.20; our IP address is 192.168.0.199
Filename 'C700A8C0.img'.
Load address: 0x400000
Loading: *#################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #############################
done
Bytes transferred = 1808528 (1b9890 hex)




Synology> bootm 0x400000



## Booting image at 00400000 ...
   Image Name:   Linux-2.6.25-numa-00000-g52237d8
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1808464 Bytes =  1.7 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux......................................................................................................................... done, booting the kernel.
Linux version 2.6.25-numa-00000-g52237d8-dirty (root@debian) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #41 PREEMPT Mon May 5 02:29:22 CEST 2008
CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=00053177
Machine: Synology DS207+/CS407/RS407
Ignoring unrecognised tag 0x41000403
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw syno_hw_version=DS207+v10 ihd_num=2
PID hash table entries: 512 (order: 9, 2048 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 125952KB available (3508K code, 256K data, 112K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 192 bytes
NET: Registered protocol family 16
Orion ID: MV88F5281-D0. TCLK=166666667.
Orion: Applying 5281 D0 WFI workaround.
PCI: bus0: Fast back to back transfers disabled
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
NET: Registered protocol family 1
NetWinder Floating Point Emulator V0.97 (double precision)
JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A
console [ttyS0] enabled
serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 4) is a 16550A
loop: module loaded
MV-643xx 10/100/1000 Ethernet Driver
eth0: port 0 with MAC address 00:00:00:00:51:81
eth0: Scatter Gather Enabled
eth0: TX TCP/IP Checksumming Supported
eth0: RX TCP/UDP Checksum Offload ON
eth0: RX NAPI Enabled
usbcore: registered new interface driver zd1211rw
Driver 'sd' needs updating - please use bus_type methods
sata_mv 0000:00:01.0: version 1.20
PCI: enabling device 0000:00:01.0 (0140 -> 0143)
sata_mv 0000:00:01.0: Applying 60X1C0 workarounds to unknown rev
sata_mv 0000:00:01.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx
------------[ cut here ]------------
WARNING: at drivers/ata/libata-core.c:5690 ata_host_activate+0x50/0x10c()
Modules linked in:
[<c0028984>] (dump_stack+0x0/0x14) from [<c0045014>] (warn_on_slowpath+0x4c/0x60)
[<c0044fc8>] (warn_on_slowpath+0x0/0x60) from [<c01c2a08>] (ata_host_activate+0x50/0x10c)
 r6:c01d1e20 r5:c7d717f0 r4:00000000
[<c01c29b8>] (ata_host_activate+0x0/0x10c) from [<c01d3a7c>] (mv_pci_init_one+0x338/0x390)
[<c01d3744>] (mv_pci_init_one+0x0/0x390) from [<c0177a60>] (pci_device_probe+0x68/0x8c)
[<c01779f8>] (pci_device_probe+0x0/0x8c) from [<c019ca24>] (driver_probe_device+0xd8/0x180)
 r7:c03a6c0c r6:c03a6c0c r5:00000000 r4:c7c11450
[<c019c94c>] (driver_probe_device+0x0/0x180) from [<c019cbac>] (__driver_attach+0x50/0x74)
 r8:c7e09e40 r7:c03a6c0c r6:c7c114f8 r5:c03a6c0c r4:c7c11450
[<c019cb5c>] (__driver_attach+0x0/0x74) from [<c019b904>] (bus_for_each_dev+0x50/0x88)
 r6:c019cb5c r5:00000000 r4:c7c1fea0
[<c019b8b4>] (bus_for_each_dev+0x0/0x88) from [<c019cbf4>] (driver_attach+0x24/0x2c)
 r7:c03a0664 r6:00000000 r5:c03a6c0c r4:00000000
[<c019cbd0>] (driver_attach+0x0/0x2c) from [<c019c0e4>] (bus_add_driver+0xbc/0x258)
[<c019c028>] (bus_add_driver+0x0/0x258) from [<c019d04c>] (driver_register+0x70/0xf0)
[<c019cfdc>] (driver_register+0x0/0xf0) from [<c01777cc>] (__pci_register_driver+0x44/0x94)
 r7:c001e2b4 r6:c03a6c0c r5:00000000 r4:c03a6bdc
[<c0177788>] (__pci_register_driver+0x0/0x94) from [<c00177a4>] (mv_init+0x20/0x5c)
 r6:00000000 r5:00000000 r4:00000000
[<c0017784>] (mv_init+0x0/0x5c) from [<c0008a60>] (kernel_init+0xbc/0x270)
 r4:00000000
[<c00089a4>] (kernel_init+0x0/0x270) from [<c0047b60>] (do_exit+0x0/0x668)
---[ end trace 501e11fd38600ca9 ]---
scsi0 : sata_mv
scsi1 : sata_mv
scsi2 : sata_mv
scsi3 : sata_mv
ata1: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0022000
ata2: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0024000
ata3: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0026000
ata4: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0028000
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-7: ST3250620AS, 3.AAE, max UDMA/133
ata1.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
scsi 0:0:0:0: Direct-Access     ATA      ST3250620AS      3.AA PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda:<3>ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
ata1.00: cmd 60/08:00:00:00:00/00:00:00:00:00/40 tag 0 ncq 4096 in
         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1: hard resetting link
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: configured for UDMA/133
ata1: EH complete
ata1.00: NCQ disabled due to excessive errors
ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen
ata1.00: cmd 60/08:00:00:00:00/00:00:00:00:00/40 tag 0 ncq 4096 in
         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1: hard resetting link
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: configured for UDMA/133
ata1: EH complete
ata1: limiting SATA link speed to 1.5 Gbps
ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
         res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
ata1.00: status: { DRDY }
ata1: hard resetting link
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: configured for UDMA/133
ata1: EH complete

This paste has no annotations.

Colorize as:
Show Line Numbers

Ads absolutely not by Google

Lisppaste pastes can be made by anyone at any time. Imagine a fearsomely comprehensive disclaimer of liability. Now fear, comprehensively.