__ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** ** MARVELL BOARD: Synology Disk Station LE U-Boot 1.1.1 (Aug 10 2007 - 19:12:18) Marvell version: 1.11.2 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB [4096kB@ffc00000] Flash: 4 MB Addresses 20M - 0M are saved for the U-Boot usage. Mem malloc Initialization (20M - 16M): Done Using default environment Soc: 88F5281 D0 CPU: ARM926 (Rev 0) running @ 500Mhz Orion 2 streaming disabled VFP initialized to Run Fast Mode. SysClock = 166Mhz , TClock = 166Mhz Model: DS-207+ CPLD version: 0x0 FAN Status: Running USB 0: host mode CPU: Write allocate enabled Net: egiga0 [PRIME] Press Ctrl+C to abort autoboot in 1 second Synology> set ipaddr 192.168.0.199 Synology> printenv bootcmd=bootm FFC00000 FFE00000 baudrate=115200 loads_echo=0 serverip=192.168.1.52 stdin=serial stdout=serial stderr=serial cpuName=926 CASset=min enaMonExt=no enaFlashBuf=yes enaCpuStream=no enaVFP=yes enaWrAllo=yes enaICPref=yes enaDCPref=yes MALLOC_len=4 ethprime=egiga0 bootargs_root=root=/dev/nfs rw bootargs_end=:::DB88FXX81:egiga0:none image_name=uImage standalone=fsload 0x400000 $(image_name);setenv bootargs $(bootargs) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end); bootm 0x400000; bootdelay=3 disaMvPnp=no ethaddr=00:00:00:00:51:81 overEthAddr=no usb0Mode=host bootargs=console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw syno_hw_version=DS207+v10 ihd_num=2 ethact=egiga0 ipaddr=192.168.0.199 Environment size: 736/8188 bytes Synology> set serverip 192.168.0.20 Synology> tftpboot *** Warning: no boot file name; using 'C700A8C0.img' Using egiga0 device TFTP from server 192.168.0.20; our IP address is 192.168.0.199 Filename 'C700A8C0.img'. Load address: 0x400000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################# done Bytes transferred = 1808528 (1b9890 hex) Synology> bootm 0x400000 ## Booting image at 00400000 ... Image Name: Linux-2.6.25-numa-00000-g52237d8 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1808464 Bytes = 1.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux......................................................................................................................... done, booting the kernel. Linux version 2.6.25-numa-00000-g52237d8-dirty (root@debian) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #41 PREEMPT Mon May 5 02:29:22 CEST 2008 CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=00053177 Machine: Synology DS207+/CS407/RS407 Ignoring unrecognised tag 0x41000403 Memory policy: ECC disabled, Data cache writeback CPU0: D VIVT write-back cache CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets CPU0: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: console=ttyS0,115200 ip=off initrd=0x00800040,4M root=/dev/md0 rw syno_hw_version=DS207+v10 ihd_num=2 PID hash table entries: 512 (order: 9, 2048 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 128MB = 128MB total Memory: 125952KB available (3508K code, 256K data, 112K init) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok net_namespace: 192 bytes NET: Registered protocol family 16 Orion ID: MV88F5281-D0. TCLK=166666667. Orion: Applying 5281 D0 WFI workaround. PCI: bus0: Fast back to back transfers disabled SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 NetWinder Floating Point Emulator V0.97 (double precision) JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A console [ttyS0] enabled serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 4) is a 16550A loop: module loaded MV-643xx 10/100/1000 Ethernet Driver eth0: port 0 with MAC address 00:00:00:00:51:81 eth0: Scatter Gather Enabled eth0: TX TCP/IP Checksumming Supported eth0: RX TCP/UDP Checksum Offload ON eth0: RX NAPI Enabled usbcore: registered new interface driver zd1211rw Driver 'sd' needs updating - please use bus_type methods sata_mv 0000:00:01.0: version 1.20 PCI: enabling device 0000:00:01.0 (0140 -> 0143) sata_mv 0000:00:01.0: Applying 60X1C0 workarounds to unknown rev sata_mv 0000:00:01.0: Gen-IIE 32 slots 4 ports SCSI mode IRQ via INTx ------------[ cut here ]------------ WARNING: at drivers/ata/libata-core.c:5690 ata_host_activate+0x50/0x10c() Modules linked in: [] (dump_stack+0x0/0x14) from [] (warn_on_slowpath+0x4c/0x60) [] (warn_on_slowpath+0x0/0x60) from [] (ata_host_activate+0x50/0x10c) r6:c01d1e20 r5:c7d717f0 r4:00000000 [] (ata_host_activate+0x0/0x10c) from [] (mv_pci_init_one+0x338/0x390) [] (mv_pci_init_one+0x0/0x390) from [] (pci_device_probe+0x68/0x8c) [] (pci_device_probe+0x0/0x8c) from [] (driver_probe_device+0xd8/0x180) r7:c03a6c0c r6:c03a6c0c r5:00000000 r4:c7c11450 [] (driver_probe_device+0x0/0x180) from [] (__driver_attach+0x50/0x74) r8:c7e09e40 r7:c03a6c0c r6:c7c114f8 r5:c03a6c0c r4:c7c11450 [] (__driver_attach+0x0/0x74) from [] (bus_for_each_dev+0x50/0x88) r6:c019cb5c r5:00000000 r4:c7c1fea0 [] (bus_for_each_dev+0x0/0x88) from [] (driver_attach+0x24/0x2c) r7:c03a0664 r6:00000000 r5:c03a6c0c r4:00000000 [] (driver_attach+0x0/0x2c) from [] (bus_add_driver+0xbc/0x258) [] (bus_add_driver+0x0/0x258) from [] (driver_register+0x70/0xf0) [] (driver_register+0x0/0xf0) from [] (__pci_register_driver+0x44/0x94) r7:c001e2b4 r6:c03a6c0c r5:00000000 r4:c03a6bdc [] (__pci_register_driver+0x0/0x94) from [] (mv_init+0x20/0x5c) r6:00000000 r5:00000000 r4:00000000 [] (mv_init+0x0/0x5c) from [] (kernel_init+0xbc/0x270) r4:00000000 [] (kernel_init+0x0/0x270) from [] (do_exit+0x0/0x668) ---[ end trace 501e11fd38600ca9 ]--- scsi0 : sata_mv scsi1 : sata_mv scsi2 : sata_mv scsi3 : sata_mv ata1: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0022000 ata2: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0024000 ata3: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0026000 ata4: SATA max UDMA/133 mmio m1048576@0xe0000000 port 0xe0028000 ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-7: ST3250620AS, 3.AAE, max UDMA/133 ata1.00: 488397168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 ata2: SATA link down (SStatus 0 SControl 300) ata3: SATA link down (SStatus 0 SControl 300) ata4: SATA link down (SStatus 0 SControl 300) scsi 0:0:0:0: Direct-Access ATA ST3250620AS 3.AA PQ: 0 ANSI: 5 sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sd 0:0:0:0: [sda] 488397168 512-byte hardware sectors (250059 MB) sd 0:0:0:0: [sda] Write Protect is off sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda:<3>ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen ata1.00: cmd 60/08:00:00:00:00/00:00:00:00:00/40 tag 0 ncq 4096 in res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) ata1.00: status: { DRDY } ata1: hard resetting link ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: configured for UDMA/133 ata1: EH complete ata1.00: NCQ disabled due to excessive errors ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x6 frozen ata1.00: cmd 60/08:00:00:00:00/00:00:00:00:00/40 tag 0 ncq 4096 in res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) ata1.00: status: { DRDY } ata1: hard resetting link ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: configured for UDMA/133 ata1: EH complete ata1: limiting SATA link speed to 1.5 Gbps ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen ata1.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout) ata1.00: status: { DRDY } ata1: hard resetting link ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata1.00: configured for UDMA/133 ata1: EH complete